How To Survive Your Boss In Repairs To Upvc Windows

Repairs to uPVC Windows

uPVC windows are a great option for modern homes. They are durable, long-lasting and easy to maintain. As opposed to aluminium and timber they are not susceptible to get rusty or decay.

It is important to clean and oil UPVC doors and windows on a regular basis. This will prevent unnecessary repair costs as well as improve energy efficiency.

1. Broken Glass

If the glass in your window is damaged, it could cause a large amount of damage to your home, which can make it very dangerous and potentially fatal. It is essential to take the time to make sure that you're doing all you can to keep your windows in good condition.

For single pane windows, it is fairly easy to replace them, and the replacement will usually fit inside the frame that was previously installed easily. If you have double-paned windows that are joined by internal beading, it is difficult to remove and replace the panes that were previously in use. In this instance, you will need to source some plastic spacers to help the new pane to fit properly into the frame of the window.

Wearing eye protection and heavy gloves is essential for anyone who plans to remove the glass by yourself. It is also recommended to lay down a dropcloth before you begin working on the window panes to ensure that any shards fall on the fabric, not onto the floor and could be trampled.

Once the glass has been removed, it's a good idea to seal the gap with packaging tape or duct tape to block water and drafts from entering the home until a professional comes out and repair the window repair. It also acts as a barrier, preventing any intruders from gaining entry to your home. If the gap between the window and the door is significant, you may prefer security screens that has windows. This will provide the best of both.

2. Sagging

uPVC windows and doors are a cost-effective energy-efficient, durable and long-lasting alternative to timber windows with sash. However, over time they are susceptible to a range of problems including sagging. A sagging uPVC window can cause issues with light, draughts, and even security. It's crucial to act as soon as you discover that your uPVC windows are sliding.

Repositioning the hinges could aid in fixing a window which is sagging. To do this, you'll need open the window to access the frame. With a screwdriver, you can take off the top and bottom hinges and adjust them by turning them clockwise or anti-clockwise. After you've repositioned the hinges, shut your window and verify the fit. If you're happy with the fit, tighten the screws until they stay in place.

If you are unable to move the hinges, you may have to replace the seal. Over time, rubber seals lose their elasticity and dry out which causes them to loosen. If this happens, it's important to replace the seal as quickly as possible to ensure your uPVC windows remain watertight and draught-proof.

uPVC handles may also loosen up. Often it is due to screws that have come loose over time. However, it could occur because the handle mechanism has been worn out. Fortunately, it's easy to fix the handle of a window that is loose yourself. First, you'll need to close your window and do an experiment to ensure that it fits. The joint at the corner of the sash should align with the joint on the casing. If it does not, you can use the screwdriver to loosen the handle. Then turn the mechanism back into place.

3. Water Leaks

It is crucial to take action if you awake each day to find a smoky wall and wet floors. Water leaks through windows can cause structural damage to your home and also affect your ability to regulate the temperature of your home. The most common cause for leaks in uPVC windows is that the sealant surrounding the frame has been damaged or not present.

This is a fairly simple fix that can be completed by any competent DIYer. Depending on the severity of the problem is, the old caulking may have to be removed. It is essential to remember that when it comes to uPVC window repairs, you should not be tempted to apply too much caulk' as this will only make the area more difficult to clean and could reduce your energy efficiency.

It is important to check that the drainage holes are clear of debris and that the sill pan is angled properly so that it drains away from the window. In more serious cases, you may need to replace the window.

Other signs of long-term water leakage are sills that are rotten and the appearance of black spots of mold on the walls near the window repairs near me. This fungus thrives in damp conditions and can spread quickly throughout the home.

If the leakage is occurring between the double-glazed glass it is more likely that the issue is with the seal rather than the frame. It is also possible to be repaired by a uPVC window expert who can replace the glass seal and restore the full insulation properties of your windows.

4. Faulty Hinges

Hinges could be at fault for the reason that your uPVC window is difficult to open or it opens in the breeze. These are easily replaced by any competent DIYer and are usually done within a few minutes.

Nearly every home in the UK will have top-hung or side-hung uPVC windows that have hinges and, just like any mechanical component they are susceptible to wear and tear over time. It is very easy to change the hinges on a window but it's much easier if someone helps you hold the frame.

It is also important to verify that the uPVC hinges are opening and closed in the right direction. You can check this by looking for the arrows on each hinge, this indicates the direction in which the window should open.

The issue could be caused either by opening the window incorrectly or due to a poor installation at the factory. This can often be resolved by sending us a photo through our website and we will be happy to give you advice.

It is also crucial to ensure that the hinges are lubricated on a regular basis. Applying a light engineering lubricant on the hinges is a good way to do this. We suggest using the lubricant that doesn't contain solvents, such as 3-in-1 Multi-Purpose oil. Regular lubrication will make the window easier to open and close. It also helps prevent corrosion and uPVC window repairs decrease the chance of sticking. Ideally, you should do this at least once a year. WD40 or other solvent-based lubricants should not be used as they could damage your uPVC windows.

5. Draughts

Draughts in windows made of upvc can be caused by a variety of different factors. The hinges can also be unbalanced due to wear, causing an opening where the sash and frame meet. This can be easily repaired by giving them a thorough clean, however when they're beyond repair, it may be necessary to get them re-aligned or replaced. The interlock may also become misaligned. This happens on the hinge's side and may need to be cleaned. In some cases, it may be necessary to replace them.

The seals may wear out or be damaged over time, allowing air to escape. Replacing these with high-quality weatherstripping can help stop draughts. Another option is to replace the upvc window with low-emissivity glass, this will help in regulating indoor temperatures and will reduce the possibility of draughts.

One of the most effective ways to cut down on drafts is to use a draught excluder, these are typically fabric tubes that are filled with some kind of filler. They can be positioned on top of your windowsill. They can help stop cold air from entering and keep your home warm and cosy!

Your windows made of upvc will keep providing excellent insulation and security for your home with regular maintenance and repairs. It is essential to remember that all windows will eventually wear out and it is more cost-effective to replace them rather than repair them. So, if you are experiencing issues with your Upvc windows, it is always best to seek professional assistance immediately.