Repairs To Upvc Windows The Process Isn t As Hard As You Think

Repairs to uPVC Windows

uPVC is a fantastic option for modern homes. They are easy to maintain and are durable and long-lasting. They don't decay or rust as aluminum and timber.

It is important to clean and oil UPVC windows and doors regularly. This will save you from costly repairs and increase energy efficiency.

1. Broken Glass

The broken glass in your windows can cause significant damage to your home and may even be fatal. You should take the time to ensure that your windows are in good working order.

Single-pane windows are fairly simple to replace and typically fit into frames that were previously in use very easily. However when windows with double panes are held in place by internal beading, it will be more difficult to remove the panes that are in place and replace them with new ones. In this instance, you will need to locate some plastic spacers to assist the new pane to fit properly into the frame of the window.

If you are going to attempt to remove the glass panes yourself it is crucial to wear the proper safety gear such as gloves that are thick and protective eyewear. It is also a good idea to lay down a drop cloth before you start working on the glass, so that any shards will fall onto the cloth instead of landing on the floor where they could be trampled on and cause further damage.

It's a great idea to seal the gap after the glass is removed. This will stop drafts and water from getting into your property until a professional arrives to fix the window. This will also act as a barrier that will prevent any intruders from gaining entry into your home. If the gap is particularly large, you might be interested in a security door that has an integrated window as this will offer the best of both worlds.

2. Sagging

Upvc is a long-lasting energy-efficient, cost-effective and economical alternative to timber sash window. Over time, they can be affected by a variety of issues that include sagging. A window that isn't properly aligned can cause problems with light, draughts and upvc Window repair even security. It's important to take action immediately if you notice your uPVC windows are falling down.

To fix a sagging window you can try to reposition the hinges. To do this, you'll have to open the window to access the frame. Then, using a screwdriver, you can take off the top and bottom hinges and adjust them by turning them clockwise or counter-clockwise. Close your window to test the fit after you have relocated your hinges. If you're satisfied with the fit, tighten the screws to ensure they remain in the right place.

If you are unable to reposition the hinges, you might need to replace the seal. Rubber seals can dry out and lose their elasticity with time, leading them to lose their tightness. It is essential to replace your seal as quickly as you can to keep your uPVC window watertight and draughtproof.

uPVC handles can also loosen up. Most often this is due to screws that have become loose over time. However, it can occur because the handle mechanism has worn out. It's a good thing that it's simple to repair a loose uPVC window handle yourself. First, you'll need close the window and perform an initial test fit. The joint at the corner of the sash must align with the joint on the casing. If it isn't then you can use a screwdriver to loosen the handle and then turn the mechanism back into the position it was in.

3. Water Leaks

If you're waking up to damp floors and mouldy walls each time it rains, it's crucial to take action. The leaks of water through windows could cause structural damage to your home and also hinder your ability to control the temperature of your home. Most of the time, uPVC window leaks are caused by a damaged or missing sealant.

It is a fairly easy fix that can be completed by any skilled DIYer. Depending on the severity of the problem the caulking used previously may need to be removed before a new layer can be applied. It is important to remember that when it comes to uPVC window repairs you should not be tempted to apply too much caulk in order to make the area more difficult to clean and can reduce your energy efficiency.

It is crucial to make sure that any drainage holes are clear of debris and that the sill pan has been angled properly so that it drains away from the window. In more severe cases, you may need to replace the window.

Mold spots and rotted sills are also signs of water leakage. The fungus thrives in humid conditions and can propagate quickly throughout the home.

It is also important to keep in mind that if the leakage is coming from between the glass in your double glazed windows it may be more likely to be an issue with the glass seal, rather than the frame or sagging. A uPVC specialist can easily fix this issue by replacing the glass seal. This will restore the full insulation of your windows.

4. Faulty Hinges

If your uPVC windows are brittle to open, or slack and open with a breeze it could be hinges at fault. They can be easily repaired by any skilled DIYer and can usually be done within a few minutes.

Nearly every home in the UK will have top-hung or side-hung uPVC windows that are hinged and, just like any mechanical component they are susceptible to wear and tear over time. Changing a window hinge is essentially a very simple procedure, but it is easier to do with someone else to help hold the frame in place.

Check that the uPVC hinges are closed and open in the correct direction. Look for the arrows on each hinge to determine which direction the window should be opened.

The problem can be caused by opening the window improperly or a faulty installation in the factory. This can often be resolved by sending us a photo on our website. We will be pleased to offer you advice.

It is also essential to grease the hinges regularly. This can be done by applying a light engineering oil to the hinges, we recommend using a solvent-free lubricant such as 3-in-one Multi-Purpose Oil. Regular lubrication can help the window open and close more easily. It can also prevent corrosion and reduce the possibility of sticking. It is recommended to do this once a year. WD40 and other solvent-based lubricants are not recommended as they will damage parts of your uPVC window.

5. Draughts

Draughts in Upvc windows can be caused by a variety of different things. The hinges can also be disaligned as a result of wear, creating gaps between the frame and sash. If they are damaged beyond repair, it could be required to realign them. The interlock may also become misaligned. It is located on the hinge side and might require to be cleaned. In certain instances it is possible to replace these.

The next most common cause of draughts is the window seals, these can become worn down or damaged over time, and will allow air to escape through the gaps. Replacement of these with high-quality weatherstripping can help stop draughts. Replace the windows made of upvc with low-emissivity glasses. This will help regulate indoor temperatures and decrease the possibility of draughts.

Another method of reducing draughts effectively is by using a draught-excluder. These are usually fabric tubes filled with a filler that can be put on top of your window sill. They will keep your home warm by blocking out cold air.

Your windows made of upvc will keep providing excellent insulation and security in your home with regular maintenance and repairs. It is important to remember that all windows will eventually become worn out, and it may be cheaper to replace them than to repair them. If you are experiencing problems with your upvc window repair windows, it's recommended to seek assistance from a professional immediately.