Guide To Nissan Qashqai Key Fob: The Intermediate Guide In Nissan Qashqai Key Fob

Reasons Why Your Nissan Qashqai Key Fob Won't Work

The Qashqai has a distinct SUV-like feel due to its larger dimensions, and the 19-inch wheels on Ti and ST-L models can be a bit spongy at times. The front tyres may lose grip on rough surfaces and its CVT could occasionally exhibit wrist-flexing torque steer.

This is usually the result of dead batteries that can be replaced in a matter of minutes. Make sure the replacement battery is the same voltage, size and specifications.

Water Damage

One of the most common reasons that a Nissan key fob will give the "key ID is not correct" message is due to water damage. The key fob has rubber seals that shield the electronic chip inside. However, prolonged exposure to moisture can cause it to cease functioning properly. It is common to observe this if your key fob was dropped in the water or a swimming pool. It can also occur when it is wet from rain or soapy hand.

If your key fob has been exposed to water for a lengthy duration, it might have to be cleaned using isopropyl ethanol or electronic cleaner. Or, it could need to be taken to an expert to repair or replace it.

If your key fob does require replacement the process is easy. First, ensure that you have a multipack with the correct battery (CR2032 3V). Then, open the front and back cases with an abrasive screwdriver. You'll need to remove the metal retaining clips and push out the battery that was in place, and then replace it with the new one. Reassemble the fob and replace the mechanical key. Verify that it is working properly. If it isn't then you'll have to bring it to a local Nissan dealer or an expert auto locksmith to repair the chip on the key. The chip is usually not damaged by water, so it should not be too expensive.

Dead Coin Battery

Another reason that your Nissan Qashqai key fob might not work is that the battery inside is dead. They typically last for 3 to 5 years, but they are susceptible to becoming depleted over time, particularly if the fob is frequently dropped. You can replace the battery, but make sure it is the same voltage and same size as the previous. If you choose to use another battery, it may cause the key to have an incorrect key ID that could hinder it from pairing with your vehicle.

The best method to replace the battery in the Nissan Qashqai key fob is by opening the fob with a small flat head screwdriver. The screwdriver should be put into a small cut on the bottom of the key fob. Make sure to gently twist the screwdriver to divide the two halves. Remove the old CR2025 battery and replace nissan key fob it with a new one, noting the position of the previous one inside the fob.

Check the terminals for dirt or water damage prior to installing the new battery. If so clean the terminals using small amounts of isopropyl alcohol. You'll also want to ensure that the pole cables are plugged in correctly. They must be connected to the negative and positive poles of the battery, respectively.

Fault Diagnosis

If your Nissan Qashqai key fob stops working after exposure to pure rain or Nissan Qashqai key fob tap water, it may be an indication of a chip issue inside. A battery change won't solve this, and you'll have to buy the new key fob. If you dropped the key fob on the ground and it stopped working instantly, this is most likely due to the damage to the internal chip. You can usually get the key fob to work once again if it is removed and clean the chip using alcohol and paper towels before putting it back into.

A common error that you may see on the dashboard of your car is "Key ID Not Correct." This means that the car cannot recognize the key fob and not allow it to start the engine. This issue can be caused by numerous ways, including water damage, malfunctions that are not detectable in the key fob circuitry or RFID interference.

If the 12 volt battery in your key fob is empty or isn't supplying enough electric current it will cease to function. This will affect your Nissan Qashqai's remote keyless system central locking, as well as the capability to start the engine using the key fob. Check the batteries inside the key fob if you're not able to lock and unlock your door by hand. Try reconnecting the battery in order to reset your transmitter.

Reprogramming

If the key fob has not been submerged in salt water, it should be able to return to life after a simple rinse with clean water. You can also clean the electronic chip by using isopropyl or electronic cleaner. If none of these works it is possible to replace the key fob.

If your Nissan Intelligent Key still does not work, there could be a connection issue between it and the vehicle. Start by turning the ignition key but not activating the vehicle. Continue doing this until the hazard lights flash twice. Turn off your vehicle and remove the key.

Open the fob compartment in your vehicle's fob compartment. It's usually in a door jamb on the driver's side door handle or underneath an armrest. Find the small "program" button and press it. You will hear a chime when the process is completed.

Now that your Intelligent Key is relinked to the car now is the time to try it out. Press all the buttons on the key while you are at a distance from the vehicle. If the lights flash and the horn sound it means the key has successfully connected to the Nissan. You may also try testing the key in close proximity.