The Most Common Mistakes People Make With Repairs To Upvc Windows

Repairs to uPVC Windows

uPVC is a great option for modern homes. They are easy to maintain, durable and long-lasting. They don't decay or rust as aluminum and timber.

Cleaning and lubricating regularly UPVC windows and doors is essential. This will reduce repair costs and improve energy efficiency.

1. Broken Glass

If the glass in your window is damaged, it can cause a great deal of damage to your home, which can make it extremely dangerous and possibly fatal. It is crucial to take the time to make sure that you are doing everything you can to keep your windows in good repair.

Single-pane windows are fairly simple to replace and typically fit into frames that were previously in use very easily. However If windows with double panes are held in place by internal beading, it'll be more difficult to get rid of the old panes and put in new ones. In this situation you'll need to find some plastic spacers that will help the new pane to fit correctly into the window frame.

Wearing eye protection and thick gloves is essential if you plan to remove the glass yourself. You should also lay down a drop cloth before you begin working on the window panes to ensure that any shards of glass fall onto the fabric and not onto the floor, where they could be trampled.

After the glass has been removed, it's a good idea to cover the gap with some clear packaging tape or duct tape to stop drafts and water from entering the property until a professional can come out and repair the window. It also acts as an obstacle to stop intruders from getting into your home. If the gap between the door and the window is substantial, you may prefer security screens that has windows. This will give you the best of both.

2. Sagging

uPVC is a durable, energy-efficient and affordable alternative to timber sash window. However, with time, they are susceptible to a range of issues like sliding. A sagging window in uPVC can cause issues with light, draughts and even security. It's crucial to act as soon as you discover that your uPVC windows are sliding.

To fix a window that is sagging you can try repositioning the hinges. First, you'll need to unblock the windows so you can access the frame. With the screwdriver, you'll be able to take off the top and bottom hinges and adjust them by turning them clockwise or counter-clockwise. After you've repositioned the hinges, shut your window and verify the fitting. If you're satisfied with the fit of your window repair, you can tighten screws to secure them in place.

If you are unable to move the hinges, you might need to replace the seal. As time passes, rubber seals lose their elasticity and dry out, which causes their tightness to decrease. If this happens, it's crucial to replace the seal as quickly as you can to ensure that your upvc window repairs near me windows remain watertight and secure from draughts.

UPVC handles can also loosen. This is typically caused by screws that have become undone over time, but it could also be due to the mechanism of the handle wearing out. It's fairly simple to fix a loose uPVC handle. The first step is to close the window and then perform a test to ensure that it fits. The corners of the sash should align with the casing joint. If it isn't then you can use the screwdriver to loosen the handle. Then, turn the mechanism into position.

3. Water Leaks

It is crucial to take action if you awake each day to discover mouldy walls and floors that are wet. The leaks of water from windows do are not just a cause for degradation of your home's structure but also hamper your efforts to control the temperature in your home. The most common reason for leaking uPVC windows is that the sealant around the frame is damaged or is missing.

This is an easy fix that can be done by any DIYer who has the ability. Based on the severity of the issue the caulking that was used up might need to be removed before a new layer of caulk can be applied. When it is time to uPVC repair, you should be careful not to over-caulk. This will only make your window harder to clean and lower its energy efficiency.

Check that any drainage holes do not have debris inside them and ensure that the sill pan is properly angled to drain away from the window. In more serious cases, you may need to replace the window.

Other signs of long-term water leakage are decayed sills and the appearance of black spots of mold on the wall near the window. The fungus thrives in humid conditions and can propagate quickly throughout the house.

If the leakage is occurring between the double-glazed window, it is more likely the issue is more with the seal than the frame. A uPVC specialist can easily fix this issue by replacing the glass seal. This will ensure the complete insulation of your windows.

4. Faulty Hinges

If your uPVC windows are stiff to open, or slack and blow open in a breeze, it may be hinges at fault. Anyone with the skills to fix them can replace hinges in just a few minutes.

Like any mechanical component hinges will wear out over time. Changing a window hinge is essentially a simple process but it can be simpler with someone else to help you hold the frame in place.

Make sure that the uPVC hinges are closed and open in the correct direction. Check for the arrows on each hinge to determine the direction in which the window should be opened.

Window hinges that aren't working properly could be the result of incorrectly opening the window in a certain manner or because of inadequate installation at the factory. It is usually possible to fix the issue by sending us a photo through our website and we will be happy to give you suggestions.

Regular lubrication of the hinges is also necessary. Applying a light engineering lubricant to the hinges is a good method to accomplish this. We recommend using the lubricant that doesn't contain solvents, such as 3-in-1 Multi-Purpose oil. Regularly lubrication will help the window to open and close more easily. It can also lower the possibility of a window sticking and help prevent corrosion. This must be done at a minimum every year. WD40 or Replace other solvent-based lubricants are not recommended as they can damage your uPVC windows.

5. Draughts

Draughts in windows made of upvc can be caused by a variety of different things. Firstly the hinges, again because of wear and tear, can become misaligned, this can cause gaps to develop between the sash and the frame. If they're beyond repair, it might be necessary to have them realigned. The interlock, which is located on the hinge side of the window and can also become misaligned, again it's possible to just give them a thorough clean, however in some cases it might be necessary to have them replaced.

These seals can wear down or get damaged over time, allowing air to escape. This can be prevented by replacing them with high-quality weatherstripping. Another alternative is to replace the upvc window with glass that is low-emissivity, this will help in regulating indoor temperatures and will lessen draughts.

The final method to cut down on the amount of draughts is to use a Draught-exclusion device. These are typically fabric tubes filled with a filler, which can be put on top of your window sill. They can help keep cold air out and keep your home warm and cosy!

The windows made of upvc can remain a great source of insulation and security in your home by performing regular maintenance and repairs. It is crucial to keep in mind that all windows will eventually get worn out and it is cheaper to replace them instead of fixing them. If you are experiencing issues with your Upvc window it is recommended to speak with a professional as soon as possible.