The No. 1 Question That Anyone Working In Fiat Panda Key Fob Replacement Should Know How To Answer

Reasons Your fiat tipo key 500 Key Fob Won't Work

A fiat 500 key fob is a handy way to open the doors and begin the car. However, there are numerous reasons why the fob won't be working. It could be due to a dead battery damage to the receiver module, issues, or interference.

This listing is for a NEW replacement Fiat Flip Key Remote that is similar to the Ilco brand. It must be professionally programmed (click here to find local locksmiths in the automotive industry). It includes lock, unlock and trunk buttons.

Dead Coin Battery

The most common reason your 500 key fob will not work is the battery is dead. Modern key fobs have a restricted operating range, and must be within a few feet of the vehicle to operate. If you're not close to your vehicle when you press the key fob button the car won't respond, and will display a "Key Fob Not Detected" message in the instrument cluster.

If this happens, simply replace the battery in the coin cell (Part number CR2032) with a new one from a trusted brand such as Panasonic, Duracell, or Energizer. You can typically find them at your local hardware store or online.

You can test the battery in the coin-cell by pressing the buttons while standing near your Fiat Key Fob Not Working 500. The parking lights should blink and the key fob should operate the lock and unlock switches.

If the key fob won't work after replacing the battery, it may be damaged by water that blocks it from communicating with the receiver module inside your vehicle. Water damage can occur in a number of ways, from a light splash to submerging the fob into salt water at the beach. If you suspect that your fob has been exposed to water, put it in a rice bag to draw out the moisture. If this does not work, you'll need to have your fob reprogrammed either by an auto locksmith or dealer.

Water Damage

Water damage can happen if you submerge the fob in the ocean or wash it in a washer. Saltwater can cause the circuit board to become shorted and eventually end up dying. It's not a good idea to get the fob wet but don't give up even if you accidentally drop the fob in water or fail to take it out of your pocket.

First take the battery off the fob. Before replacing the battery clean the electronic chip using isopropyl or another similar product. Check the fob to see if it is working. If the key does not function, Fiat 500x key fob programming it may need to be programmed again. This is usually done by a professional or dealer auto locksmith.

If the key is newer and was not programmed to your car It will most likely need to be replaced completely. A professional locksmith for cars will be able to complete this process. The locksmith will need to cut the key to match the ignition of your car. They will also need to reprogram the fob for your car's system. This is a cheap and fast process that can be completed on the same day.

Receiver Module Issues

One of the main reasons why your 500 key fob might stop working is because it's out of range. The remote has a range of 30 feet. So should you be too far away from your vehicle it won't be able to respond to your commands. You can easily solve this problem by moving the remote closer to your vehicle until it responds.

If your fob does not work after replacing the battery in the coin, also called a "button", "watch" or "button", it could be a problem with the internal circuit board. Reprogramming the fob typically resolves this problem. You can find the procedure for the majority of vehicles on YouTube or in the owner's guide.

It is sometimes necessary to replace the metal clips that hold the coin batteries in their place. If they lose tension, it could prevent the coin battery from being seated properly and can cause your remote to malfunction.

In rare cases the fob may be out of sync with your vehicle because of software or hardware problems. This could be a huge issue, but you are able to often fix this by visiting a local dealer or auto locksmith to reprogram your fob for you. In certain instances it is possible that the software will require reinstallation into your body control modules.

Interference

In addition to a dead coin battery The key fob might not be able to transmit or receive an signal due to interference. This could occur if the key fob is in close proximity to a radio transmitter, such as a cell phone or radar detector. The key fob may not work due to a poor connection with the buttons, water damage or damage to the internal chips.

If your key fob suddenly stopped working, or if you've tried everything at home to fix it (e.g. You could have a malfunctioning 500 receiver module if you've tried replacing the battery, reprogramming it, or using a spare key fob. The receiver module, located under the dashboard, detects radio frequency signals from your key fob. It transforms the signals into electronic commands, which are then processed by the vehicle.

There is a simple way to reset the 500's onboard system, including the keyfob. Disconnect the battery of 12 volts for approximately 15 minutes by removing the negative cable first then the positive cable. Reconnect the battery. This will clear any residual electricity, and allow you to restart the computer of your car. This will help you get your key fob to work again. If the issue continues, you should seek the advice of an expert technician. They will be able to identify the root cause of any issues.