Ten Things You ve Learned In Kindergarden Which Will Aid You In Obtaining Fiat Panda Key Fob Replacement

Reasons Your fiat punto car key 500 Key Fob Won't Work

A key fob for Fiat 500 allows you to easily open doors and start your car. There are many reasons the fob won't work. This could be due to a dead coin-battery and water damage, as well as issues with the receiver module, and interference.

This listing is for an NEW Replacement Fiat 500 Key Fob Fiat Flip Key Remote - look-alike Ilco brand that needs to be programmed professionally by a local automotive locksmith (click here to search for a Locksmith Search). It comes with lock, unlock and trunk buttons.

Dead Coin Battery

A dead battery is the most common reason for your 500 key fob not functioning. Modern key fobs have a very limited range of operation, and must be within a few feet of the vehicle to operate. If you're far from your vehicle when you press the key fob button, the car won't respond, and will display the "Key Fob Not Detected" message in the instrument cluster.

If this happens, simply replace the battery in the coin cell (Part number CR2032) with a fresh one from a reliable brand like Panasonic, Duracell, or Energizer. You can usually find them at your local hardware store or on the internet.

After you've replaced the battery of your coin cell It is possible to test it by standing in front of your Fiat 500 and pressing the buttons. The parking lights will flash and the key fob should operate the lock and unlock switch.

If the key fob won't function after replacing the battery, it might be damaged by water that blocks it from connecting to the receiver module in your vehicle. Water damage can happen in many ways, such as an easy splash or submerging your key fob in saltwater at the beach. If you suspect that your fob was exposed to water, you can place it in a bag of rice to draw out the moisture. If that doesn't work your fob may need to be reprogrammed by a professional locksmith or dealer.

Water Damage

While the fob comes with rubber seals that keep water out of the electronic chip inside, submerging it in the ocean or washing it in a machine could cause water damage. Saltwater poses a particular risk to the circuit board of the fob and can cause it to short out and eventually die. It's not the best idea to soak the fob in water but don't give up even if you accidentally drop the fob in the water or don't remove it from your pocket.

First take the battery off the fob. Before replacing the battery, clean the electronic chip with isopropyl, or a similar product. Check the fob again to check if it's functioning. If the key does not function, it may have to be programmed again. This is usually done by an auto locksmith or dealer.

If the key is more recent and has not been programmed to your vehicle It will most likely need to be replaced completely. This is an easy process which can be accomplished by a professional automotive locksmith. The locksmith will need to cut the key to match the ignition on your vehicle. They'll also need to program the fob into the car's system. It's a simple and cost-effective procedure that can usually be completed in the same day.

Receiver Module Issues

Your 500 key fob might not function because it's out of range. The remote usually has an area of 30 feet or less and if it's far from your vehicle, it will not respond to your commands. This can be fixed by moving it closer to your vehicle until it starts responding.

If your fob won't work after replacing the battery inside the coin, which is also called a "button", "watch" or "button", it may be due to a malfunction on the internal circuit board. In the majority of cases, reprogramming your fob can resolve the problem. The instructions are available for most vehicles on YouTube or in the owner's manual.

You may need to replace the metal clips that hold the coin battery. If they lose tension it could prevent the battery from being seated properly and cause your remote to malfunction.

In rare cases the fob might be out of alignment with your vehicle because of hardware or software problems. You can fix this problem by visiting your local dealer or auto-locksmith to reprogram your key fob. In some cases the software might require reinstallation into your body control modules.

Interference

In addition to a dead coin battery The key fob may not be receiving or transmitting signals due to interference. This could occur if the key fob is close to radio transmitters (cell phones and radar detectors) or another source of electromagnetic radiation. Other reasons the key fob may not function include a poor connection to the buttons, damage to the internal chip, or water damage.

If your key fob suddenly stopped working, Replacement Fiat 500 Key Fob or you have tried everything at home to resolve it (e.g. replacing batteries, reprogramming or using the spare key fob, you could have a faulty receiver module on your 500. The receiver module is located under the dash and picks up the radio frequency signals from the key fob. It transforms the signals into electronic commands, which are then interpreted by the vehicle.

There is a straightforward method to reset the 500's on-board system, including the keyfob. Disconnect the battery of 12 volts for about 15 minutes, by taking off the negative cable first then the positive cable. Reconnect the battery. This will eliminate any remaining electricity, and allow you to restart the car's computer. This can help you get your key fob working again. If the issue continues, you should consult an experienced technician. They will be able diagnose the exact cause of issues.