How To Tell If You re At The Right Level To Go After Saab 9-3 Key Replacement

How to Replace the Replacement Key Battery For the saab 9-3 replacement key 9-3

Saab owners must follow a set of specific steps to add a second ignition key. It requires dealer support using a handheld computer dubbed Tech-2. A new key and transponder must be purchased and then programmed into the car.

It is a good idea to rotate your keys in order that one doesn't wear out faster than the other. This will help to keep your keys in top condition.

Replacement Case

Contrary to the classic Saab keys of the past keys, the new keys have electronic components which makes it hard to create a duplicate. This has made stealing car keys significantly more difficult than 20 years ago. However, it also has made replacing lost keys a comparatively costly endeavor.

Saab 9-3 owners should have two keys working. It is expensive to replace a lost key as it requires replacing the CIM module, as well as programming the locking cylinders. Dealers usually charge between $100-$200 to complete this.

There are ways to reduce these costly. Some parts dealers will search for the code from a spare key (usually the same one that opens the doors and turns the ignition) and cut a brand new key blade from metal for less than the dealer's cost. The key must be the exact identical to the original one for it to function in your vehicle.

Follow these steps to replace the case. You will need a flathead screwdriver as well as some patience. With the screwdriver slowly pull the plastic apart and separate the emergency keys from the case. Once you have the case open, remove the electronic components and place them into the new case. Be sure to put the correct badge and key back into the case as well.

Replacement Battery

The replacement battery for the Saab 9-3 is a cheap component that can be replaced quickly and easily. Cyclone's YouTube video Cyd demonstrates the procedure for replacing the battery of the remote fob with only four steps. This tutorial can be used for any modern saab-type key fob, saab Key programming however, the procedure may differ slightly.

The first step is to locate the button that will release the backup key within the fob. This button is typically located on the back of your fob right next to the Saab Logo. Next use a flathead screwdriver into the small hole of this button. This should be enough to unlock the fob's case to allow you to replace the battery.

Once you have installed the new battery CR1632, you are able to reassemble your remote key fob. You can then program it into your car. The entire process shouldn't take more than an hour. It is a simple procedure that doesn't require any special equipment.

The process can be a bit more complicated if you lose the key, but it's possible. The dealer will need to verify the VIN of the car, and then request a replacement key blade and a TWICE module with the correct unique code. The dealer will then have to program the key using MDI which is a new software tool.

Replacement Key Fob

The key fob is the piece that locks and unlocks your car. It has batteries inside. Batteries are able to last for a short time and will eventually die. This is a typical issue that happens to all cars and the good news is that you can change the batteries in a majority of key fobs without having to replace the entire case. You can buy replacement fobs from Amazon that include all the electronics already installed, so you'll be able to just pop open the case and replace the batteries in the original case. It is important to note that you'll need to remove the emergency key first. you can do this by inserting a small flathead screwdriver into the slot in the middle of the case. Use the screwdriver to move around the case until it will split open, making it simple to take it out.

If you're ready to change your keys, be sure to have a spare in your possession. This will save you lots of money. If you have an extra key, you can request the dealer to cut it and program it for your vehicle. This is much cheaper than purchasing a new key fob.

It is possible to add a second key to your car If you don't already have one, but it takes a great deal of research and effort. Adding a second key costs around a hundred dollars and also requires programming of the car's computer. Professionals can accomplish this however it's a costly option.

Replacement Ignition

In contrast to earlier Saab automobiles, the current SAAB 9-3 models feature an extremely sophisticated alarm system that is built around a coded key. If you lose your primary key, it can be costly to replace it with another one since the car must have a specific computer installed and also be programmed to accept a new key. Locksmiths typically aren't able to program this or even dealers will charge hundreds of dollars just to program the new key!

Dealers will charge you a premium to replace your car's computer (also known as the CIM or SAAB twice) if you lose the only working key. Instead, we can reprogram the EEPROM in your current car computer to make it ready to accept a second key, slashing over 50% of the amount you have to pay at a dealership.

If you've been an owner of a 03-11 saab Key Programming 9-3, then you likely are aware that the ignition key isn't very robust. They can get extremely sticky, and the buttons can fall off of them occasionally and you should think about replacing your ignition key if it isn't working properly. The good news is that replacing the ignition key isn't as complicated as it seems and can be done quickly using the appropriate tools.